Posted on

DMX512: Resources

Application Note 0201 – DMX & RDM Introduction. This includes wiring details for XLR and RJ45.

Application Note 0205 – DMX & RDM Splitters. What are they and where to use them.

Application Note 0215 – DMX & RDM Marking. Howe to interpret splitter marking symbols.

Application Note 0210 – DMX & RDM Splitter Comparison. Compare Artistic Licence splitters.

FAQ:

Q: What is maximum cable length for DMX512?

A: 300m

Q: Can I use Cat5?

A: Yes

Q: How do I terminate:

A: With products that use an XLR, you can connect a terminator plug. With DIN-Rail products, there is an internal terminator which is connected enabled by fitting a wire link between TERM and DATA+.

Posted on

Guides: Power over Ethernet

Power-over-Ethernet or PoE defines the way that an ethernet cable can be used to send both power and data to a product. The product which uses PoE is called a ‘PD’ (Powered Device) and the product which supplies the power and data – often an ethernet switch – is called the ‘PSE’ (Power Sourcing Equipment).

PDs require differing amounts of power depending upon their design and the load they are driving.

PSEs are capable of supplying different amounts of power.

These variables are addressed by a number of IEEE standards:

  • PoE is described by IEEE802.3af-2003. It allows a maximum of 15.4W to be supplied.
  • PoE+ is described by IEEE802.3at-2009. It allows a maximum of 25.5W to be supplied.
  • PoE++ is in development and will be described by IEEE802.3bt-2017. It allows a maximum of 90W to be supplied using all 4 pairs. There are 4 different power levels available: 38.7W, 52.7W, 70W and 90W.

The wattages described above refer to the power made available by the PSE. As there are significant losses in the cable, the amount of power available at the PD is lower.

Posted on

Software products – Windows compatibility

After Windows XP, Microsoft significantly changed the way in which application software can communicate with Windows. This means that in Vista, Windows 7, 8 and 10 some of our software products must be run in a special mode. This mode is called Windows XP compatibility mode with administrator rights. See the application note.

The product concerned is Mic-Edit.

Posted on

Guides: LED dimmer selection

There are three key methods of dimming LED: mains, constant current (CC) and constant voltage (CV) .

  • Mains dimmers are used with LED replacement bulbs.
  • CC dimmers put out a controlled current, which means that the fixture does not need electronics for current control of the LED. This style of dimming is used for higher power LED products.
  • CV dimmers put out a constant voltage and the current control is done by the LED fixture. This type of dimming tends to be used for the lower power LED products such flexible tape.

It is important to choose the correct technology of dimmer as an incorrect choice will most likely damage the fixture. Below is a summary of the dimmers offered by Artistic Licence:

Mains

sunDial quad is DMX512/RDM controlled 4-channel, mains powered trailing edge dimmer. 1kW total at 230 VAC. 

Constant current or constant voltage

candlePower octo is a DMX512/RDM controlled LED dimmer with 8 channels. Each channel can be individually set to constant current (CC) or constant voltage (CV) dimming.

  • Voltage: 10-60VDC
  • Current Max: 2A per channel
  • Control: DMX512 / RDM
  • Form: DIN Rail

Constant voltage only

Rail-Pipe HC is a high current DMX dimmer for 2 x RGB circuits (6 channel).

  • Voltage: 12-24VDC
  • Current Max: 20A per product, 10A per RGB circuit
  • Control: DMX512 / RDM
  • Form: DIN Rail
Posted on

Guides: The DALI Guide

Artistic Licence offers a broad range of DALI products.

There is a very large speed difference between DMX512 and DALI, which means that care must be taken when designing a lighting installation that uses both protocols. Artistic Licence has prepared The DALI Guide (see below) to assist all DALI users and installers, particularly those who are more familiar working with DMX512.

the%20dali%20guide